SwedenSkatteverket
Electricity tax relief for metallurgical processes now covers ladle heating
Since 1 January 2026 ladle heating qualifies; mineralogical processes stand in their own paragraph with furnace heating only.
By Taxxa AI OyPublished 18 November 2026
Industry: Manufacture of basic metals · Manufacture of other non-metallic mineral products
Electricity consumed in metallurgical processes is exempt from energy tax on electricity under certain conditions. A taxable consumer takes the exemption as a deduction (11 kap. 9 § first paragraph point 5 lagen (1994:1776) om skatt på energi); a consumer that is not taxable receives it as a repayment (11 kap. 13 a § first paragraph point 4 of the same law). The exemption applies only to the extent no deduction or repayment right follows from the preceding points of those paragraphs.
Since 1 January 2026 the exemption covers more than furnace heating.Skatteverket It now also covers electricity consumed for heating ladles (skänkar) or similar vessels where the changed properties the input material acquired through earlier furnace heating are retained.
Skatteverket Previously the exemption was limited to energy-intensive furnace processes in which chemical or inner physical material changes take place.
Skatteverket The widening came through SFS 2025:1357
Skatteverket, and older provisions still govern consumption before 1 January 2026 under its transitional provision
Skatteverket. Skatteverket's 2022 position that ladle electricity fell outside the exemption (dnr 8-1772676) no longer applies to consumption on or after 1 January 2026; the replacement position of 9 January 2026 (dnr 8-5227-2026) governs instead.
For the exemption the input material must have changed chemically through heating in furnaces or have had its inner physical structure changed, or those changed properties must be retained in the ladles or similar vessels.Skatteverket The metallurgical process runs from sinter production to ingots, billets or castings and includes the continued processing of those products in reheating and heat-treatment furnaces; forming and treatment also fall within the concept. Examples are melting raw material such as pig iron, scrap, alloys and residues in a furnace to produce a casting, and heat-treating steel in a chamber furnace where the heating changes the material chemically or structurally.
Electricity for other purposes alongside these processes remains outside the exemption: mechanical work, lighting and similar uses, as well as electricity used solely for drying.Skatteverket Electricity consumed in a furnace during periods when it holds no material is covered where the furnace is being heated before material is placed in it, or material has been removed after a completed process and new material has not yet been placed in it.
Mineralogical processes now stand in their own paragraph.Skatteverket Repayment for electricity consumed in mineralogical processes requires the input material to have changed chemically through heating in furnaces or to have had its inner physical structure changed
Skatteverket, and only electricity used for heating the furnaces in those processes qualifies
Skatteverket. The same exclusions for mechanical work, lighting and drying-only use apply there.
Legal basis is 11 kap. 9 § first paragraph point 5 and 13 a § first paragraph point 4 lagen (1994:1776) om skatt på energi in the wording from 1 January 2026 (SFS 2025:1357)Skatteverket.
Producers heating ladles or similar vessels to retain material properties should claim the electricity exemption for consumption from 1 January 2026 and keep mineralogical-process claims to furnace heating only.
Sources
- Metallurgiska processer
- Återbetalning av skatt på el och bränsle
- skatteverket 8-1772676 - Metallurgisk process – elförbrukning i skänkar och liknande kärl
- skatteverket 8-5227-2026 - Ställningstagandet ”Metallurgisk process – elförbrukning i skänkar och liknande kärl” ska inte tillämpas på elförbrukning som sker efter att lagändringar trätt i kraft den 1 januari 2026